Many people, men, women and children included, in several Asian and Middle Eastern societies wear a distinctive type of head wear for religious, cultural and practical reasons. It is a covering made from twisting a single length of fabric around their heads to form a high circular formation that encompasses the top skull section. These are instructions on how to wrap a turban in one a style that is commonly worn.
The process begins by placing a tight fitting cotton cap over one's head. It should be brimless and of solid color without any type of ornamentation such as embroidery or jewels. The purpose of this covering is to protect the hair from becoming tangled in the cloth as it is wrapped and to keep the final product looking neat.
The covering will be made from a single length of fabric that needs to be a yard wide and at least six foot long, longer if one wishes to have a larger finished product. Material is a personal choice that may be based on the purpose for which one is wearing the hat. Prepare for the process by halving the cloth four times along the long side until it is roughly about four inches in width.
Take one of the short ends and hold it at the lower right hand side against the nape of the neck. Start by bringing the length of cloth up over the head bearing left high above the ear. Keep going by crossing the forehead towards the right and back around to the rear, coming low behind the ear and back around the base of one's hairline.
As one continues wrapping towards the left side, it should be brought up low behind the ear and then up and across forehead again. The point where the two layers intersect should create an "X" right at the hair's base line. Until one has had the chance to practice the technique, this first part may seem quite awkward but it will quickly become more comfortable with each try.
Continue wrapping in like manner only each time around, leave approximately one inch of the previous round showing beneath the new one. With each fresh pass, the circles will become a bit wider and a little higher. This is how the classic layered and rounded look is ultimately achieved.
Once the full length of cloth has been wound, take the last layer of fabric and tuck it into the others for a rounded finish. Parts of skull cap will still be visible right at the crown of the head and this is as it should be. Carefully release that very first wrap from its position on the bottom, understanding it will tug at the neck and the piece that was initially held in place at the nape will pull up and come out, hanging loose.
One it has been released, gently unfold it and spread it out across the exposed cap and smoothing it to a smooth layer. Take the loose ends and secure them by tucking under those that are rounding the center. By following these instructions on how to wrap a turban, most anyone will be able to create a classic look that can be personalized with just a few variations.
The process begins by placing a tight fitting cotton cap over one's head. It should be brimless and of solid color without any type of ornamentation such as embroidery or jewels. The purpose of this covering is to protect the hair from becoming tangled in the cloth as it is wrapped and to keep the final product looking neat.
The covering will be made from a single length of fabric that needs to be a yard wide and at least six foot long, longer if one wishes to have a larger finished product. Material is a personal choice that may be based on the purpose for which one is wearing the hat. Prepare for the process by halving the cloth four times along the long side until it is roughly about four inches in width.
Take one of the short ends and hold it at the lower right hand side against the nape of the neck. Start by bringing the length of cloth up over the head bearing left high above the ear. Keep going by crossing the forehead towards the right and back around to the rear, coming low behind the ear and back around the base of one's hairline.
As one continues wrapping towards the left side, it should be brought up low behind the ear and then up and across forehead again. The point where the two layers intersect should create an "X" right at the hair's base line. Until one has had the chance to practice the technique, this first part may seem quite awkward but it will quickly become more comfortable with each try.
Continue wrapping in like manner only each time around, leave approximately one inch of the previous round showing beneath the new one. With each fresh pass, the circles will become a bit wider and a little higher. This is how the classic layered and rounded look is ultimately achieved.
Once the full length of cloth has been wound, take the last layer of fabric and tuck it into the others for a rounded finish. Parts of skull cap will still be visible right at the crown of the head and this is as it should be. Carefully release that very first wrap from its position on the bottom, understanding it will tug at the neck and the piece that was initially held in place at the nape will pull up and come out, hanging loose.
One it has been released, gently unfold it and spread it out across the exposed cap and smoothing it to a smooth layer. Take the loose ends and secure them by tucking under those that are rounding the center. By following these instructions on how to wrap a turban, most anyone will be able to create a classic look that can be personalized with just a few variations.
About the Author:
Discover how to wrap a turban with top tips from this informative website www.turbanizer.com. For guidance, see the related homepage today athttp://www.turbanizer.com.
No comments:
Post a Comment